Part 1 - Damaging Walls:(Other parts of this post are found further down)
Following on from my posts about the construction of my Siege Towers, I've started work on the natural enemy of every Siege Tower ever constructed: a Castle!
It might seem an odd way round to do things (Towers first, Castle second) but there was good reason. I've got a Siege game coming up this summer so there's time to prepare both with not much rush-factor. I've had one of the original Citadel "Mighty Fortress" sets for a very long time - getting on for 20 years or so but the paint job I applied to it back then was very basic (but usable in a pinch so if I did run short of time I could get away with it as it is).
Also, I wanted to be able to be a bit more flexible with the castle construction for the game than the Mighty Fortress set allows, so I've been on the hunt for a second set. I recently picked one up from ebay so I've got everything I need now to get started.
Each set comes with 4 x Towers, 4 x Wall sections and 2 x Gate sections. As I said I have two of these so I have four Gate sections. No castle on the planet is ever going to want four Gates, so I decided early on that I was going to sacrifice two of the Gate sections in order to be able to model some "Breached" and "Collapsed" wall sections.
Here's a picture of the first Breach - I used everything from a Stanley blade to a hacksaw to chop this thing up - it's only made of Polystyrene Foam but it's a dense, solid block so it took some hacking!
The arch section is shown here back in place in the wall to give an idea what it looked like before I started.
The arch section will get chopped up later in order to form a "collapsed" section and some rubble and suchlike.
According to the Warhammer 6th Edition rulebook (which is as far as I can tell the last place a Siege rule supplement was published) I need to be able to represent various stages of damage:
- Ramparts Destroyed (I feel something magnetty in the offing there),
Part 2 - Damaging Towers:I'm generally getting better at hacking. Since my first post I've successfully carved up another Gate section to make the pieces for another Breach and have also chopped the "arch" section into rubble that I'll scatter about the place to make it look like these walls have genuinely fallen down rather than just had a bit "teleported away".
I'll not bother you with photos of more broken polystyrene until it's all painted up - you've seen a breach above and one hole looks much like another.
I've applied the same techniques to create a partially collapsed tower (the paintjob on this tower is an old one I did a looong time ago and will be overpainted later):
I've pretty much settled on the technique I'm using:
- Hacksaw a jagged line from top to bottom,
- Use an Exacto-blade to roughen up the cut lines to give texture,
- Then along the line of the cut, use the Exacto-blade to remove the occasional stone block.
Part 3 - "Smash it up!"As I mentioned above, there are a number of different types of damage to represent. I've built two sections to represent a "breach" in the walls:
Another section was built to represent a complete collapse using the same methods:
Part 4 - Damaged RampartsOne of the damage types the 6th Edition Siege rules call to be represented is damage to the ramparts which means that troops on that castle section can still move around but can't gain cover. Theoretically this can occur on a tower or wall section, and a wall section can either be a regular wall or a wall with a gateway in it.
Now I don't have enough castle pieces available to sacrifice that many sections over and above what I've already sacrificed on this project, so I needed to devise a way of making damaged ramparts that could be swapped out for regular ramparts.
Since the model is made from polyfoam, I decided to cut the ramparts from my nominated sections - it's a solid model with no "space" within and as such both the walls and the ramparts I removed would be quite sturdy even when chopped up. My first attempts to do this were with a hot-wire cutter which were, frankly, disastrous. The HWC cut through the castle easily enough but I found it impossible to maintain a neat, straight cut along the whole length of the section I was removing.
I opted in the end to use a blade for a snap-off DIY knife, but without the handle attached. This gave me a very flat blade that was about 8'' long and very, very sharp. I could lay it flat on the walkway section of the ramparts and slide it along cutting deeper into the back of the rampart wall with each pass. It didn't take long to work all the way through and left a neat cut (and several not so neat cuts in my fingertips!).
I then cut some plasticard rectangles to fit the gap and drilled some holes through them. These holes would ultimately hold gaming magnets, but I first used them as templates to make marks on the top of my castle walls and the bottom of the excised ramparts. These were bodged into holes and magnets inserted into all three pieces (superglued into the plasticard and epoxied into the castle/ramparts):
I then decorated the plasticard section with a bit of gravel and some polystrene chunks to represent the remains of the battlements - here's what it looks like in place:
And swapped out for the battlements:
The same principle was applied to another wall section and a gate section - I won't bother showing these until some paint has been applied. I also did one tower:
The polystyrene isn't as sturdy as the polyfoam and looks a bit "cloudy" in these photos, but the cellular structure of it does give is a "damaged stone-y" sort of texture and I'm hoping with a layer of paint over it it should look OK.
Well, I know I'd promised that the last update I did on this build was going to be the last one, but something was bugging me.
Part 5 - Ruined Tower:I'd built a ruined tower section which I really didn't like. In fact I didn't like it so much I'd actually not shown it before, even though it's been "finished" for a few weeks. Here it is now:
My plan was to try and texture the walls, but the problem was that the polystyrene I'd used wasn't up to the job. There are different grades of "expanded polystyrene" and the one I'd used to build the tower was very soft (I suppose the gradings are all about just how much the polystyrene has been expanded by). This stuff was made of small "balls" or "cells" which were about 2mm across and quite "squashy". I became concerned about how much abuse it could withstand and also how I could go about adding texture to it. I was planning to just draw on a wall-pattern with a pen, leaving indentations in the foam, but it didn't work - the cells ruptured and came away.
So I trashed it and started again. This time I've used foamcore - I sliced off one side of the card outer leaving just a card back and the foam centre. Happily, I made a ham-fisted job of it which actually left me with a nicely undulating surface which serves to add to the detail. Some work with a ball-point pen and I now have a sturdier, textured tower:
I'm going to start a new post shortly on my adventures in painting the castle. Stay tuned.